How we work

We always follow the same five steps. Simulation sits in the middle: the real shape of the vehicle comes before it, the track comes after.

AI-generated image: a competition car in profile with illustrative streamlines, not a simulation result
Provisional image
This image is AI-generated and stands in as a placeholder while the site is being built. We'll replace it with our own photos and renders.
Simulation stage
  1. 01

    Scan

    3D model

    We scan the vehicle or the part, or start from an existing CAD model, then run a metrology check to make sure the measurements are right.

  2. 02

    Sim

    Simulation

    We put the part in the flow at the speeds you actually reach on track, and note the ride height and configuration we used.

  3. 03

    Iter

    Iteration

    We change the shape, rerun the simulation and compare it with the previous version. We keep going until load, drag and balance sit together the way we want.

  4. 04

    Prod

    Production

    The shape we settle on becomes the file we build the part from, with no hand tweaks in between.

  5. 05

    Track

    Track check

    We fit the part and test it on track. The simulation tells us which way to go, but the stopwatch always has the last word.

ILLUSTRATION
Inverted aerofoil in a left-to-right flow. Animated illustration, for demonstration only.

What we measure

We look at four things, and each one holds for a specific speed and configuration.

  • Downforce

    This is the force the air uses to press the car onto the tarmac. It gives you grip in fast corners without adding weight, and it grows with the square of speed. On bikes we also watch the opposite effect, the lift that lightens the front end.

    On kit pagesΔDownforce · ΔLift · N

  • Drag

    This is the resistance the air puts up against forward motion. Any part that makes load also makes drag, and you pay for it in top speed on the straight. That's why a part is judged by its ratio of load to drag.

    On kit pagesΔDrag · N · L/D efficiency

  • Balance

    This is how the load splits between front and rear. A part that loads only one axle shifts the balance and changes how the vehicle behaves in fast corners.

    On kit pagesAero balance (front) · %

  • Pressure fields

    These are the pressure maps on the surfaces and the lines the air follows around the part. They show us where it speeds up, slows down and separates, and explain where a number comes from.

    On kit pagesWindLab images

Stated limits

A simulation is only as good as its conditions.

  1. CFD is a computer calculation and always simplifies reality a little. A measurement on track is always a must.
  2. The numbers depend on speed, ride height and the vehicle's configuration. Change one of those and the numbers change too.
  3. A result holds for the vehicle and configuration we simulated. On another model, or the same one with a different set-up, the simulation becomes less reliable.
  4. The simulation shows us the way, then the track confirms it.

How we publish figures

When a kit has simulation data, we'll always write it this way. If a number is missing its speed or its conditions, we don't publish it.

Format of a CFD figure on a kit page. Layout only, no values.
  1. Quantity

    What is being measured. The Δ symbol marks a difference between two vehicle configurations, described in the conditions.

  2. Value and unit

    The value that comes out of the WindLab simulation, with its unit. We write that, without rounding it into nice-sounding percentages.

  3. Reference speed

    We always state it. Aero forces grow with the square of speed, so a number without a speed tells you nothing.

  4. Simulation conditions

    Speed, front and rear ride height, vehicle configuration, yaw angle. They tell you the situation in which the figure holds.

  5. Method note

    The same on every CFD block: these are simulation figures, to be read as a comparison between configurations.

WindLab post-processing

This is where we'll put the real images from our simulations: pressure fields and streamlines, exported from WindLab.

COMING SOON

Pressure field

COMING SOON

Streamlines

COMING SOON

Wake and flow separation

CFD analysis

Got a part you want to put to the test?

We can simulate a part you already have or one you want to develop with us.